KDG HD DVR Remote Control

[tiveria]

Hi,

i tried to learn the codes of the KDG Remote control that is shipped as part of their 4 tuner hd dvr.
i'm using a standard IRTRans USB V3.8 with Firmware U6.06.30

The problem is, that even if i only try to learn one button, i get tons of different timings and codes (see rem extract below - always pressed ok).
From trying out the commands i found that the only correct one is the timing with RCMM detected - 2.
Why is this only detected a few (4) times? what do i need to set have better results (RCMM detection is activated in gui client)

BR
Michael





[REMOTE]
[NAME]test

[TIMING]
[0][N]4[1]352 2944[2]152 1400[3]152 2008[4]152 3344[RC]1[RP]0[FREQ]36[SB]
[1][N]5[1]144 464[2]152 624[3]144 792[4]352 1560[5]152 1960[RC]1[RP]0[FREQ]38
[2][N]5[1]168 280[2]168 440[3]416 280[4]168 608[5]168 776[RC]2[FL]100[FREQ]36[RCMM]
[3][N]7[1]144 464[2]144 632[3]144 792[4]152 1072[5]152 1240[6]352 1560[7]152 2568[RC]1[RP]0[FREQ]38
[4][N]6[1]152 464[2]144 632[3]152 792[4]152 1240[5]352 1552[6]144 1960[RC]1[RP]0[FREQ]38
[5][N]7[1]208 240[2]152 464[3]144 632[4]144 792[5]144 1240[6]144 1968[7]352 2168[RC]1[RP]0[FREQ]38
[6][N]6[1]200 248[2]200 408[3]152 624[4]168 776[5]160 1392[6]360 2160[RC]1[RP]0[FREQ]38
[7][N]6[1]144 464[2]144 632[3]152 792[4]152 1400[5]144 1968[6]352 2168[RC]1[RP]0[FREQ]38
[8][N]8[1]144 296[2]144 464[3]144 632[4]152 736[5]144 1072[6]144 1248[7]144 1408[8]352 1560[RC]1[RP]0[FREQ]38
[9][N]7[1]144 296[2]144 464[3]152 624[4]152 792[5]352 784[6]144 1072[7]144 1240[RC]1[RP]0[FREQ]38
[10][N]6[1]136 472[2]152 624[3]152 792[4]152 1176[5]144 1408[6]352 2168[RC]1[RP]0[FREQ]38
[11][N]7[1]160 456[2]152 624[3]152 736[4]144 1072[5]144 1240[6]144 1408[7]352 1560[RC]1[RP]0[FREQ]38
[12][N]5[1]144 464[2]152 624[3]144 800[4]152 1064[5]352 2168[RC]1[RP]0[FREQ]38
[13][N]6[1]144 304[2]144 464[3]144 632[4]152 792[5]144 1520[6]352 1560[RC]1[RP]0[FREQ]38
[14][N]6[1]192 280[2]152 456[3]144 632[4]152 792[5]144 1960[6]352 2168[RC]1[RP]0[FREQ]38
[15][N]5[1]144 464[2]144 792[3]144 1248[4]352 1560[5]144 1968[RC]1[RP]0[FREQ]38
[16][N]5[1]144 464[2]144 632[3]152 792[4]352 1560[5]144 2568[RC]1[RP]0[FREQ]38
[17][N]6[1]152 464[2]152 624[3]152 792[4]144 1240[5]352 1552[6]144 2568[RC]1[RP]0[FREQ]38
[18][N]6[1]144 464[2]152 624[3]144 792[4]352 1560[5]152 1848[6]152 1960[RC]1[RP]0[FREQ]38

[COMMANDS]
[ok][T]0[D]310152401420
[a][T]1[D]301024010020
[b][T]2[D]203131400031311400
[c][T]3[D]504261320
[d][T]2[D]203131400031311400
[e][T]4[D]40102503020
[f][T]2[D]203131400031311400
[g][T]5[D]62135411300
[h][T]6[D]52400021211300
[i][T]7[D]5134010020
[j][T]8[D]71260325430
[k][T]9[D]42613032125300
[l][T]10[D]5143130020
[n][T]12[D]410223010020
[m][T]1[D]301024010020
[o][T]13[D]5121304121130
[p][T]14[D]521341211300
[q][T]15[D]3021402010
[r][T]2[D]203131400031311400
[s][T]16[D]30102410020
[t][T]17[D]4032510020
[u][T]4[D]40102503020
[v][T]18[D]3425010020
[w][T]1[D]301024010020

[IRTrans]

Hi,
you can try to activate "Force RCMM detection" in the device settings (GUI Client).

RCMM uses very short pulses. In general the standard IR Receiver cannot detect those pulses very well.
The learning receiver (COD-RCV) is better in learning such IR codes.

IRTrans