Which IRTrans device to purchase

Here is the place for all Hardware and Firmware related questions

Moderator: marcus

Which IRTrans device to purchase

Postby wimt » Tue 26. Jun 2012, 21:02

Dear Madam/Sir,

I need some advice for the following.

Devices to control:
- Pioneer TV PDP-505XDE : volume +/-, source selection
- Samsung HD CableReceiver DCB-H360RS: channel selection
- Bang&Olufsen 3200 Beosound : volume up/down, source selection
- Samsung TV 46D8000: power on/off, volume +/-, channel selection
- Sharp portable air conditioner CV-P09FR: (less important device) power on/off

Ways to control:
By sending http requests to the irtrans device

Requirements: wifi capable irtrans, standalone capable

Question:
Which devices and eventually add-ons do I need to purchase to accomplish these goals ?

Thanks in advance,
Wim
wimt
 
Posts: 5
Joined: Tue 26. Jun 2012, 11:51

Re: Which IRTrans device to purchase

Postby IRTrans » Tue 26. Jun 2012, 23:38

Hi,
for this setup you will need:

IRTrans WiFi IRDB
Internal Learning Receiver
External High Power Transmitter for B&O
Power supply

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Which IRTrans device to purchase

Postby wimt » Wed 27. Jun 2012, 09:00

Thank you for the quick reply.

I've checked in http://www.irtrans.de/en/shop/wifi.php.
Still a few things:

1. Are these mappings to order numbers correct ?
IRTrans WiFi IRDB == IRT-WiFi-DB
External High Power Transmitter for B&O == IRT-RCV-HF
Power supply == POW-SUP

2. I could not find the 'Internal Learning Receiver' you've suggested.
Could you give me the order number ?

3. Is this setup suited for about 7 to 8 meters line-of-sight ?

4. What is the extra benefit for a second ir output (order nr. IRT-WiFi-2X) ?

Regards,
Wim
wimt
 
Posts: 5
Joined: Tue 26. Jun 2012, 11:51

Re: Which IRTrans device to purchase

Postby IRTrans » Wed 27. Jun 2012, 12:08

Hi,
regarding your questions:

IRTrans WiFi IRDB == IRT-WiFi-DB
External High Power Transmitter for B&O == IRT-TRANS-HPK with the remark "for B&O"
Power Supply == POW-SUP

The internal learning receiver is "COD-RCV"

7-8m line of sight should work.

The 2nd IR Output can be used to control 2 devices of the same make and model independently.

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Which IRTrans device to purchase

Postby wimt » Wed 27. Jun 2012, 14:40

Ok. That's clear. So I should order:
- IRT-WiFi-DB
- IRT-TRANS-HPK with the remark "for B&O"
- POW-SUP
- COD-RCV

Now the last(I hope) two questions before my purchase.
1. With the above combination, could I use the B&O Beo4 to control the other non-B&O devices , and the other way around, control my Beo 3200 from a non-B&O remote ?
2. I'm using a Mac as my main desktop where I also control an Openwrt zwave/router(Vera, always on) and a Linux box.
As far as I can see, the only difference is the iRed license between these:
Would I have more possibilities if I order the IRT-WiFi-MAC instead of the IRT-WiFi-DB ? (Assuming that I can install a isserver on the Linux box when needed)

Thanks again,
Wim
wimt
 
Posts: 5
Joined: Tue 26. Jun 2012, 11:51

Re: Which IRTrans device to purchase

Postby IRTrans » Wed 27. Jun 2012, 15:21

Hi,
the above combination will allow you to learn and send B&O and Standard IR Codes.

To Translate IR Codes from one system to another you will need the correct IR Receivers for that system (Either B&O or Standard).
It is, however, not possible to have more than one IR Receiver. That means you can either control B&O with a standard remote or the other way round.
For both combinations you would need to have the correct external IR Receiver connected.

The WiFi Mac device has got the iRed license instead of the Windows/LINUX license.

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Which IRTrans device to purchase

Postby wimt » Wed 27. Jun 2012, 15:42

IRTrans wrote:Hi,
the above combination will allow you to learn and send B&O and Standard IR Codes.

To Translate IR Codes from one system to another you will need the correct IR Receivers for that system (Either B&O or Standard).
It is, however, not possible to have more than one IR Receiver. That means you can either control B&O with a standard remote or the other way round.
For both combinations you would need to have the correct external IR Receiver connected.

snip

IRTrans


Ok. Now I'm aware that I'll have to choose between controlling 'standard' from B&O and controlling B&O from 'standard'.

Please bear my fussing:
As I want to be able to switch between these possibilities (can't make up my mind now), which extra device do I need to purchase in addition to mentioned list ?

Thank you,
Wim
wimt
 
Posts: 5
Joined: Tue 26. Jun 2012, 11:51

Re: Which IRTrans device to purchase

Postby IRTrans » Wed 27. Jun 2012, 21:56

If you want to do both you will need:

IRT-RCV 38kHz receiver
IRT-RCV-HF 455kHz receiver

In case you have a plasma TV in the same room you will need the plasma shielded versions:

- IRT-RCV-PLA
- IRT-RCV-HF-PLA

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Which IRTrans device to purchase

Postby wimt » Thu 28. Jun 2012, 11:03

Hi Irtrans,

Thanks for your nice hardware and your pre-sales-support and patience !
I'm going to order as soon as possible.

Regards,
Wim
wimt
 
Posts: 5
Joined: Tue 26. Jun 2012, 11:51


Return to Hardware

Who is online

Users browsing this forum: No registered users and 14 guests

cron