Hello,
I have a Lan I/O with 4 external IR outputs. I have managed to install it without no problem and is working fine. Using GUIclient I can control every external zone (from 1 to 4) separately without any problem (select form the Led Select drop down list All/Default/External/1/2/3 or 4 and all are working as they should).
I have installed the Homeseer plugin and I have configured it accordingly (Hostname localhost, Use Zones: checked, Ir learning bus: Bus0). I can define devices/learn/send commands and is working ok until I try to use zones. Lets say I have a device ARTEL on the IR Output 1 (exit the Homeseer, test the device using GUIClient - select Led 1 - , works ok, exit GUIClient, start Homeseer again). In the Zone Name or Device Name table the Output Zone is set between 1-120 (always get the same results but let's say is 120). Press Send and the device is working (note: the device is in another room so there is no way that the Lan's I/O internal led is sending the signal). I get the following log in Homeseer:
2/19/2011 1:57:21 AM - IRTrans Debug - SetZone(120) called
2/19/2011 1:57:21 AM - IRTrans Debug - PlayIR() called on location: 3
2/19/2011 1:57:21 AM - IRTrans Debug - zoneEnding=20
2/19/2011 1:57:21 AM - IRTrans Debug - Bus is 0, Address mask will be 00000000 00000000 00000000 00000001
2/19/2011 1:57:21 AM - IRTrans Debug - Command played successfully.
2/19/2011 1:57:21 AM - IRTrans Debug - KeyLearnable() called with location 0
2/19/2011 1:57:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 1:57:21 AM - IRTrans Debug - KeyLearnable() called with location 1
2/19/2011 1:57:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 1:57:21 AM - IRTrans Debug - KeyLearnable() called with location 2
2/19/2011 1:57:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 1:57:21 AM - IRTrans Debug - KeyLearnable() called with location 3
2/19/2011 1:57:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 1:57:21 AM - IRTrans Debug - KeyLearnable() called with location 4
2/19/2011 1:57:21 AM - IRTrans Debug - SupportsIR2() called, returning true
Now I have changed the zone to 121 and is still working (normally it should NOT work I think).
Zone 122 is NOT working (normally it should work I think) and I get:
2/19/2011 2:16:04 AM - IRTrans Debug - SetZone(122) called
2/19/2011 2:16:04 AM - IRTrans Debug - PlayIR() called on location: 3
2/19/2011 2:16:04 AM - IRTrans Debug - zoneEnding=22
2/19/2011 2:16:04 AM - IRTrans Debug - Bus is 0, Address mask will be 00000000 00000010 00000000 00000001
2/19/2011 2:16:04 AM - IRTrans Debug - Command played successfully.
2/19/2011 2:16:05 AM - IRTrans Debug - KeyLearnable() called with location 0
2/19/2011 2:16:05 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:16:05 AM - IRTrans Debug - KeyLearnable() called with location 1
2/19/2011 2:16:05 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:16:05 AM - IRTrans Debug - KeyLearnable() called with location 2
2/19/2011 2:16:05 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:16:05 AM - IRTrans Debug - KeyLearnable() called with location 3
2/19/2011 2:16:05 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:16:05 AM - IRTrans Debug - KeyLearnable() called with location 4
2/19/2011 2:16:05 AM - IRTrans Debug - SupportsIR2() called, returning true
Zone 123 and 130 are working (I can move the IR Output jack from 1/3 to 2/4 and is working with both).
Zone 131 not working and I get:
2/19/2011 2:07:21 AM - IRTrans Debug - SetZone(131) called
2/19/2011 2:07:21 AM - IRTrans Debug - PlayIR() called on location: 3
2/19/2011 2:07:21 AM - IRTrans Debug - zoneEnding=31
2/19/2011 2:07:21 AM - IRTrans Debug - Bus is 0, Address mask will be 10000000 00000010 00000000 00000001
2/19/2011 2:07:21 AM - IRTrans Debug - Error playing command 3: IR Error: Selected IR Output does not exist
2/19/2011 2:07:21 AM - IRTrans Debug - KeyLearnable() called with location 0
2/19/2011 2:07:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:07:21 AM - IRTrans Debug - KeyLearnable() called with location 1
2/19/2011 2:07:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:07:21 AM - IRTrans Debug - KeyLearnable() called with location 2
2/19/2011 2:07:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:07:21 AM - IRTrans Debug - KeyLearnable() called with location 3
2/19/2011 2:07:21 AM - IRTrans Debug - SupportsIR2() called, returning true
2/19/2011 2:07:21 AM - IRTrans Debug - KeyLearnable() called with location 4
2/19/2011 2:07:21 AM - IRTrans Debug - SupportsIR2() called, returning true
In conclusion I cannot control interdependently the external zones using Homeseer (as I said earlier the zones can be controlled fine using the GUIClient ).
I am using a registered version of Homeseer (Standard Edition 2.5.0.1) and the Irtrans plugin (1.2.15.0) downloaded using Homeseer updater
Thanks for helping me,